Electromotive-TEC -III-R

The TEC combines state-of-the-art fuel injection with the industry leading Direct Ignition System, replacing the existing carburetor or fuel injection system, ignition, distributor and coil. The use of advanced, digital computer based technology offers the absolute best power delivery, smoothest drivability and lowest emissions possible. Unlike any other fuel control system, TEC needs only two inputs to establish the base fuel curve. Where other systems rely on huge tables that must be filled with individual pulse width values, TEC is based on thermodynamically linear fuel delivery. You get up and running quicker with greater flexibility and better results than any other system available.

The new TEC³r represents the current in state-of-the-art fuel injection and direct ignition control integrated into one revolutionary package. The TEC³r is a PC-programmable engine control system featuring a powerful Windows-based tuning environment. Converting from carburetion to fuel injection has never been easier than with the TEC³r. Whether you choose to run throttle body injection, multi-port, or individual throttle bodies, the TEC³r will provide you with the ability to tune your engine to its peak capabilities.

Street enthusiasts will enjoy the benefits of a ‘distributorless’ ignition system that not only is infinitely adjustable, accurate, and powerful, but also gives you improved firewall clearance and freedom from all those ignition amplification boxes that you used to run in the past. If you are running an aggressive profile camshaft, idle control has always proven to be problematic for lesser engine management systems, but not for the TEC³r. Within the WinTEC3 software resides our exclusive ‘TPS/MAP Idle Blend’ table. With a few clicks of the keyboard, you will enjoy an idle quality that other engine management systems only dream of having.

For competition and ultra high output engines, the sophistication and power of the TEC³r system simply out-performs other production and aftermarket systems. With full control of the engine over all possible operating conditions, outputs that will control nitrous, boost, VTEC, and other devices, new rev-limiters with ‘Triple Smooth’ technology, and On-Board Data Acquisition, the TEC³r gives you Total Engine Control...and makes the competition green with envy!

The TEC³r Engine Control Unit

The new TEC³r ECU incorporates the winning features of our previous TEC2 and TEC3 system while adding an abundance of new features and a powerful new processing platform. Electronic Fuel Injection (EFI) control and patented digital Direct Ignition control is standard hardware for every TEC3r. The anodized, laser-etched ECU with waterproof OEM style connectors and harness may be mounted under the hood or in the passenger compartment and will activate separate multi-coil DFU’s (Direct Fire Units) mounted adjacent to (or on) the engine.

Standard features built in to the TEC³r:
PC programmable and configurable for 1, 2, 3, 4, 6, 8, 12 cyl. engines and Rotaries
Operate in Open or Closed loop
Run True Sequential, Phased Sequential or Simultaneous Injection with individual cylinder trim
Configurable for TBI, MPI, TPI and individual throttle bodies
Additional Injector Output Drivers built-in.. Run Low or High impedance injectors
Full 150 mJ of Spark Energy directly to the plugs without misfire
New Dual Rev Limiters with ‘Triple Smooth Technology’.. 1st step retards timing to a negative -12º degrees.. 2nd step cuts coil current in half.. 3rd step coil current and fuel are cut-off.. all three steps occurring within milliseconds!
Waste Gate (Boost Control), Nitrous Control with up to 4 stage retard available
Four Programmable GPO’s (General Purpose Outputs) to control or activate VTEC, Shift Lights, Water Pumps and Fans, A/C Compressor, Torque Converter and more.
New Programmable Adjustable Electronic Tachometer Output
Uses primarily GM type sensors
Diagnostic monitoring with codes issued through Check Engine Light
Easy to install bolt-on Trigger Wheel and Mag Sensor Kits available for many applications
Made in the USA

New On-Board Data Acquisition Adjustable Sample Rates up to 100 samples per second Simultaneously record data from up to 25 inputs including: Air/fuel Ratios, Injector Duty Cycle and Pulse Width, RPM and Throttle Position, Gear Position, MPH, Boost (manifold pressure) and much more!
Additional configurable Digital and Analog Input Channels View Multiple Data Graphs side by side or Graphs may be overlaid for comparison. Graphic Screen Displays may be Printed.
Data may also be exported to a Spreadsheet program for further analysis. Data Logging can be started and stopped manually using a switch, or the system can be configured to automatically start and stop via values pre-set by the user.

The TEC³r Engine Management System will run the following configurations:
4 cylinder 6 cylinder 8 cylinder 12 cylinder Up to 16 low impedance injectors* Up to 8 high impedance injectors* Rotary engines 6 cylinder, dual plug
4 cylinder, dual plug STAGED OR SEQUENTIAL . My 3 .5 liter 308 below runs TEC3R in sequential mode. TEC3R is also operating the engine on the dyno video.